Price checkxTool O1 Omni: 8 preorder configurations from $1,899 to $4,169Compare prices
The Crafty CatsmanHybrid workshop field notesStart Here

A process I am researching, not reviewing

What Still Has to Happen After a Resin Print

I do not own a resin printer, so this is not an owner review. The manufacturer instructions make one thing clear: the job continues through removal, washing, drying, curing, support cleanup, and cleanup of the work area.

The short answer

A resin print can require printer and tank preparation, orientation and supports, part removal, washing, drying, post-curing, support cleanup, surface finishing, and careful handling of resin, wash material, contaminated tools, and waste. Follow the instructions and safety data sheet for the exact printer, resin, wash material, and local disposal rules you use.

Sources checked July 28, 2026

Manufacturer system exampleHeyGears UltraCraft Reflex RS Combo
  1. 01Print
  2. 02Wash
  3. 03Cure
Official HeyGears UltraCraft Reflex RS Combo product image showing the resin printer, wash station, and cure station
One manufacturer's connected equipment exampleShown as one manufacturer's example — not an owner review
Experience checkWhat I have used myself

I do not own or review a resin printer. This page summarizes the steps documented by the manufacturers linked below; it does not claim that every printer uses the same equipment. Use the instructions and safety data sheet for the exact material in your shop rather than treating this overview as a substitute.

The job continues after printing

Set up removal, washing, drying, and curing before you print.

Set out the equipment, exact material instructions, bench space, and cleanup supplies for the system in front of you before the print starts.

  1. 01Print
  2. 02Remove
  3. 03Wash
  4. 04Dry
  5. 05Cure
  6. 06Finish
Before the print01

Plan the wash, dry, cure, and cleanup space before printing.

Before sending the file, check the selected resin, tank and platform condition, orientation, supports, removal method, wash method, dry area, cure settings, and the place where contaminated tools and surfaces will be handled.

A bundle with wash and cure hardware can connect some of that equipment. You still have to remove, wash, dry, cure, and clean up the part as directed.

After the print02

After the build plate rises, the part still needs washing, drying, and curing.

Formlabs documents washing, build-platform cleaning, drying, post-curing, and support removal for its SLA process. The order and settings can change with the material and system, which is why current instructions matter.

Those steps need bench space and supplies. They also take time when a print fails, a tank needs inspection, wash material needs attention, or the next resin calls for a cleaner setup.

Safety instructions03

Use the exact safety instructions, not a generic resin checklist.

Formlabs directs users to the applicable safety data sheet and discusses ventilation, gloves, eye protection, solvent handling, and contaminated surfaces for its products. Another resin or wash material may carry different instructions.

I can point out where those safety decisions enter the job. I cannot declare one room, glove, fan, respirator, disposal method, or wash setup sufficient for every resin-printing system.

Official instructions used here

Check the exact machine and material instructions.

These pages document the steps above. Use the instructions for your exact printer and material because equipment and settings vary.

Formlabs

Quick Start Guide (Form 4)

This is the Form 4 routine. It is not a promise that every resin printer uses the same equipment or settings.

Read the official instructions
Formlabs

SLA basic finishing steps

Wash and cure steps can change with the material and equipment, so use the instructions for the resin in front of you.

Read the official instructions
Formlabs

Safety with Formlabs resin products

The resin, solvent, equipment, room, and local disposal rules all matter. Use the SDS and manufacturer instructions for the materials you actually have.

Read the official instructions
HeyGears

UltraCraft Reflex RS Combo

This shows how one manufacturer bundles the printer, wash station, and cure station. It is not a third printing process or independent proof that the bundle is easier to use.

Read the official instructions

Still choosing?

Compare filament and resin on the main 3D-printing page.

Use the main page to compare both workflows and see the full equipment checklist.

Back to 3D printing