Skip to main content
Skip to the X1 guide

In our workshop since September 2026

xTool X1 laser: specs, size and what it has made so far

This is our house.
In miniature.

We have been testing the X1 for weeks with CO₂, 20W diode and 60W MOPA sources installed. xTool sent this early unit for review. xTool confirms 55W CO₂ and lists 30W Fiber · 60W MOPA · 5W UV as supported upgrade paths.

xTool X1 orders are open. Check the configurations and prices on xTool’s page before you order; if you paid a deposit, complete your order through the link xTool emailed you.

Our own home, reimagined in laser-cut wood—with its familiar windows, tiny porch lamps and a little Halloween personality.

See our home in miniature
Our home recreated as a wooden Halloween miniature with raised shutters and pumpkins, reflected in a glass table
That is our home in miniature, dressed for Halloween. The X1 cut the wood; a separate UV printer added the color.

Checked October 31, 2026: The xTool X1 has been in our workshop since September 2026 with CO₂, 20W diode and 60W MOPA sources installed, and we have been testing it for weeks; xTool sent it for review. It is xTool’s 55W CO₂ laser cutter with swappable diode, UV, MOPA or Fiber galvo sources, launched October 28, 2026, starting at $3,399.

xTool sent this early X1 unit for review. xTool has no review or approval of our testing, results, or verdict.

By Published Updated

The project that brings it together

A familiar home.
A little Halloween magic.

This little house began with our real home: five upstairs windows, the fanlight over the front door, and the lower three-window wing. Then came the Halloween details—cats, bats, pumpkins and glowing windows.

Across three jobs, the X1 cut a 62-piece basswood layout: 61 house parts and one test frame. Separate layers form the window frames, shutters, doorway and foliage. A few small parts were cut again as the project took shape, so that layout count is not the final assembled-piece total.

A separate UV printer added the color and illustrated window scenes. The X1 gave the wood its shape; printing gave those surfaces their character.

Our miniature on our real front stoop, then a closer look at the finished house: a 24-second film, with music. The X1 cut the wood; a separate UV printer added the color.Music: “Darkest Child” by Kevin MacLeod, licensed under Creative Commons Attribution 4.0. Excerpted, gain-adjusted and faded for this video.Also on YouTube as a 33-second Short with the cutting footage: watch it on our channel.

Our real house was the starting point

The windows. The doorway. Our home.

Look at the five upstairs windows, the fanlight over the front door and the lower wing on the right. Those familiar features are what make the miniature ours. The pumpkins, little lamps and glowing Halloween scenes give it a seasonal personality.

The wooden Halloween miniature of our home lit from inside, with five upper windows, a centered fanlight doorway and a lower right wing
Our home, made miniature for Halloween and lit from inside. Photo: The Crafty Catsman
The same home interpreted as a layered wooden Halloween miniature, preserving its five upper windows, central fanlight doorway and lower right wing
Our miniature version: familiar proportions and windows, with Halloween details added in wood, print and light. Background removed from this photograph.
Close view of two tiny raised wooden porch lamps beside the miniature doorway, with layered pumpkins below
The raised porch lamps are decorative wood pieces, each designed at just 5.6 × 14.6 mm. Light shines through the doorway and windows behind them.

More time for the small things

The detail I had time to add.

For me, the X1’s autofocus and bed-leveling workflow gave me time back. I spent less of this project thinking about setup and more of it thinking about what would make the house feel like ours.

Take those tiny lamps beside the door. They were a later addition: two separate wooden profiles, then printed and raised off the facade. Along with the window cutouts, shutters and small pumpkins, they show why precise cutting matters to a project like this. These are the details I might have skipped if I were still tinkering with settings.

That is what I mean when I say smarter tools open more creative doors. The benefit was having the time and confidence to try one more detail.

My first impressions from this build; I have not measured the time saved or tested a cutting-accuracy tolerance.

First impression

These are first impressions from the weeks the X1 has been in our workshop, before any finished metal piece. They are initial reactions, not a final assessment or a score.

After weeks with the X1, our first impression is that it is an ambitious platform with a promising idea at its center: bring several laser processes into one coordinated workspace. xTool Studio guided the initial calibration, and the tutorial box moved from CO₂ cutting to diode scoring and engraving in one job. The machine has since cut parts for our personalized birthday-train project and Atomm’s five-part layered cat. Our 60W MOPA marking trials are still underway.

The Crafty Catsman · workshop first impressions

What the xTool X1 costs

xTool sells the X1 starting at $3,399 for the Single CO₂ configuration, machine only; every configuration, bundle tier and xTool’s payment terms are on our xTool X1 prices by laser configuration page.

Different laser sources, one platform

xTool describes a 55W CO₂ processing head and a galvo system supporting diode, Fiber, MOPA and UV sources. These sources interact differently with materials: CO₂ is used for cutting and engraving wood and suitable acrylic; MOPA and Fiber address metal marking; UV supports fine marking on materials such as glass. Supported source families are not a list of what comes in a retail package. Our workshop unit has CO₂, 20W diode and 60W MOPA installed.

Close view of the installed X1 source pack with its 60W label, ventilation and connected cables.
The 60W MOPA source pack mounted on the back of our X1. Photo: The Crafty Catsman

xTool’s published X1 specifications

xTool’s published X1 figures, checked October 31, 2026: maximum working area 615 × 320 mm (24.2 × 12.6 in); our unit has CO₂, 20W diode and 60W MOPA installed.

xTool X1 specifications as xTool publishes them, checked October 31, 2026 — xTool X1 launch page. The last column marks the laser sources installed on our review unit.
SpecificationxTool’s published figureInstalled on our unit
Working area
Surface engraving615 × 320 mm (24.2 × 12.6 in)Not a laser source
Glass inner engraving, top 50 mm, refractive index 1.54600 × 300 mmNot a laser source
Glass inner engraving, 50 to 100 mm deep60 × 300 mmNot a laser source
Metal embossing, with the Dust Hood for Embossing415 × 225 mmNot a laser source
Laser sources: speed and processing height
55W CO₂ laserSpeed 600 mm/s; processing height 150 mmYes
20W diode galvo moduleSpeed 6,000 mm/s; processing height 140 mmYes
60W MOPA galvo sourceSpeed 6,000 mm/s; processing height 140 mmYes
5W UV galvo sourceSpeed 6,000 mm/s; processing height 140 mmNo
30W Fiber galvo sourceSpeed 6,000 mm/s; processing height 140 mmNo
Cutting capacity, rotary, size and weight
Cutting capacity, basswood18 mmNot a laser source
Cutting capacity, acrylic20 mmNot a laser source
Rotary diameter110 mmNot a laser source
Machine dimensions1,000 × 580 × 420 mmNot a laser source
Main unit weight60 kgNot a laser source

Source: xTool’s X1 launch page(paid link), checked October 31, 2026. These are xTool’s figures, not our measurements.

How big the xTool X1 is in our workshop

Measured in our workshop on October 11, 2026, the xTool X1 is 39 1/2 in (100.3 cm) wide, 29 3/8 in (74.6 cm) deep with the 60W MOPA pack mounted, and 17 1/2 in (44.5 cm) tall.

xTool X1 machine size measured in our workshop, October 11, 2026 (tape measure, 60W MOPA source pack mounted)
MeasurementInchesCentimeters
Width, side to side39 1/2100.3
Front to back with the 60W MOPA source pack mounted, the lid’s front lip included29 3/874.6
Height of the machine17 1/244.5
Floor to the top of the machine on xTool’s X1 Mobile Work Stand45 1/4114.9

Excludes exhaust duct, access and ventilation space. Early review unit; a retail unit may differ slightly.

What we have done with the X1 so far

The X1 has been in our workshop since September 2026 with its 55W CO₂, 20W diode and 60W MOPA sources installed. We set it up through xTool Studio’s guided initialization calibration, which Studio reported complete on our first setup day, and later ran Studio’s focus calibration for the 60W MOPA and the 20W diode.

Side view of our xTool X1 with its lid raised, showing the side panel, ventilation and emergency-stop button.
Our X1 with its lid open, photographed from the side. Background removed and lighting corrected. Photo: The Crafty Catsman

Our first job was the tutorial box built into xTool Studio, xTool’s own project rather than one of ours. In that one job, the CO₂ laser cut the parts from basswood plywood and the 20W diode scored a decorative graphic and engraved xTool’s logo.

The X1 cut wooden parts for a personalized second-birthday train from 3 mm basswood. The color was added separately with a UV printer. The latest workshop photograph also shows the finished birthday locomotive.

Finished pink and cream wooden birthday locomotive with a smiling face, bow and three large wheels, held at the front edge.
The finished wooden birthday locomotive. Background removed and lighting corrected; the hand holding the front edge remains as photographed. Photo: The Crafty Catsman

We gave xTool’s Atomm AI design tool a written brief for a layered Halloween cat. It returned a five-part design, and the X1’s CO₂ laser cut all five parts from a 12-inch sheet of 3 mm basswood plywood with Atomm’s geometry unchanged. The parts are not assembled yet.

With the 60W MOPA, we are running marking trials on uncoated 16-gauge plain steel. There is no finished metal piece to show yet.

In October 2026 the X1’s CO₂ laser cut a lit gingerbread cottage from 12-inch sheets of 3 mm basswood plywood: the walls, the roof, and the sweets and trim as separate layers. A separate UV printer added the color and the raised icing, and we assembled it by hand. A revised version of the cut files is published on Atomm and on eufyMake’s Make It Real.

A wooden gingerbread cottage with a layered candy roof, a lit arched window, a snowflake cookie and a gift, standing on a sofa cushion.
The gingerbread cottage from the side: the roof, the sweets and the lit window. The X1 cut the wood; a separate UV printer added the color and the raised icing. Photo: The Crafty CatsmanCottage files and assembly guide on Atomm
The rear wall of the wooden gingerbread cottage with two arched windows and raised candy decorations.
The back of the cottage: two frosted windows, with a bow, a peppermint and a stocking added as separate cut layers. Photo: The Crafty Catsman

For the holidays the X1’s CO₂ laser cut a set of ugly-sweater ornaments and a run of coastal gift tags from 3 mm basswood, each blank cut with its own hanging hole. The knit textures, artwork and sample names were printed afterwards on a separate UV printer; the wood came off the X1 plain.

A wooden ugly-sweater ornament printed with an eagle in a Santa hat and the words Let Freedom Jingle, standing on a wooden surface.
An ugly-sweater ornament, front. The blank and its hanging hole were cut on the X1; the knit texture and artwork were printed on a separate UV printer. Photo: The Crafty CatsmanFour sweater designs on Atomm
The back of a wooden ugly-sweater ornament printed with a dark knit pattern, snowflakes and a Christmas 26 patch.
The back of an ornament, printed with the knit pattern and a year patch. Photo: The Crafty Catsman
A wooden gift tag shaped like a scalloped shell with a red bow, printed with sample To and From lines.
A coastal gift tag with its sample names. The blank was cut on the X1; the artwork was printed on a separate UV printer. Photo: The Crafty CatsmanCoastal tag files on Atomm

The CO₂ laser also cut the parts for Feather & Find, a birdhouse memory game: the house and 32 square tiles for 16 bird species from 3 mm plywood. The tile fronts are printed on a separate UV printer and photographed; the tile backs are still to print, so the game is not finished yet.

A small wooden birdhouse printed with a bluebird on a branch, a nest with eggs in the round opening and the words Feather and Find.
The Feather & Find birdhouse that holds the memory game. Cut from 3 mm plywood on the X1 and printed on a separate UV printer. Photo: The Crafty CatsmanBirdhouse and game files on Atomm
Thirty-two square wooden tiles laid out on a dark table, each printed with a named bird such as a blue jay, puffin or cardinal.
All 32 tiles, 16 bird species in pairs. The square blanks were cut on the X1; the birds were printed afterwards. The backs are still to print. Photo: The Crafty Catsman

All our X1 projects and downloads are collected on our maker page.

What we are still testing

We are still working on finished metal pieces with the 60W MOPA source. Beyond xTool’s own tutorial box, which used both the CO₂ laser and the 20W diode, our own CO₂-plus-diode project is still in progress. We are not publishing speed, accuracy, or reliability measurements from these early projects, and each finished piece will be added with the laser operation that made it.

How the platform works · from xTool’s published engineering

How the xTool X1 combines motion, structure and laser sources

A moving gantry carries the galvo, compatible laser sources share one coordinate framework, and a die-cast frame supplies the physical reference. Here is what xTool’s published engineering explains, what we have seen in our workshop so far, and what still needs checking.

The xTool X1 coordinates mechanical gantry travel with local galvo scanning and maps each supported galvo laser source to one shared coordinate system. Its 55W CO₂ laser uses a separate processing head. xTool describes three die-cast aluminum frame sections as the physical reference for motion and optics, and says up to three configured sources can work one after another within a task.

How Hybrid Motion divides the work

xTool describes Hybrid Motion as one coordinated system that pairs gantry XY travel with galvo XY scanning. The gantry carries the scanning unit across the work area, while mirrors in the galvo steer the beam within each local region. The controller divides a design into regions, plans the gantry path, and synchronizes the mechanical and optical moves.

The intended benefit is a detailed design that stays one job while the gantry advances the scanning field and the galvo handles local lines, curves, and fill. That explains the control approach; it does not establish the time or quality of a particular finished project.

The gantry moves the scanning field; the galvo draws within it.

Source: xTool Academy: Hybrid Motion explained(paid link)

Focus, positioning and calibration solve three separate problems

Focus, positioning and calibration answer different questions. Focus concerns the material surface relative to the beam’s working plane; positioning concerns where the material and the processing area sit; multi-source calibration relates the coordinates used by the different laser sources and motion systems.

What xTool says: xTool’s engineering article says the X1 vision system identifies the material and processing area, and its LaserSwap article explains the shared-coordinate calibration layer. The public xTool material we checked does not describe the X1 autofocus method or publish a camera-positioning tolerance.

What we have seen in our workshop so far: We set up our X1 through xTool Studio’s guided initialization calibration, which Studio reported complete on our first setup day, and later ran Studio’s focus calibration for the 60W MOPA and the 20W diode. Those are completions reported by the software, not measured accuracy.

Focus: surface distance. Positioning: artwork location. Calibration: shared machine coordinates.

Sources: xTool: Behind X1, an engineering challenge(paid link); xTool Academy: LaserSwap explained

Why the cast frame matters

xTool’s engineering article describes the X1 frame as three die-cast aluminum sections made with a 4,000-ton-class high-pressure process. Its UniCast article says large one-piece cast structures form the upper and lower housings, and that parts of those structures also form the visible body.

xTool describes the castings as a common mounting reference for motion and optics, with fewer joints and connection points. That is the intended structural role; long-term durability and ease of repair have not been measured here.

Design role: one stable physical reference for motion and optics. Durability and serviceability are separate questions.

Sources: xTool: Behind X1, an engineering challenge(paid link); xTool Academy: Inside xTool X1, UniCast Frame

How X1 expands across laser sources

What xTool says: The 55W CO₂ laser uses its own processing head. xTool describes a 20W diode galvo path and support for 30W Fiber, 5W UV and 60W MOPA sources. These are supported source families, not a retail package contents list. Each external source feeds the shared galvo system and has its own calibration model mapped to the same coordinate framework. xTool says X1 can use up to three configured sources one after another within a task and switches between them automatically; the sources never fire at the same time.

What we have seen in our workshop so far: Our X1 has the CO₂, 20W diode, and 60W MOPA sources installed. xTool Studio guided the initial calibration. The tutorial box built into xTool Studio used the CO₂ laser and the 20W diode in one job. That does not establish every source combination or which modules suit each configuration.

In general, CO₂ is the cutting and engraving workhorse for wood, acrylic, and leather; diode light suits fast engraving; Fiber and MOPA mark metal, and MOPA can also produce color on some metals; UV marks heat-sensitive materials such as glass and many plastics.

CO₂ uses its own head. The diode and the Fiber, MOPA, and UV modules share the galvo path and one coordinate framework.

Sources: xTool Academy: LaserSwap explained; xTool: Behind X1, an engineering challenge(paid link)

These explanations describe the platform as xTool presents it. On their own they do not establish measured accuracy or finished-work quality or say which modules suit each configuration, and this first look does not supply settings or setup instructions.

xTool X1 questions

How much does the xTool X1 cost?

The price depends on which laser sources you choose. Our xTool X1 price page lists every laser configuration, with the date we checked xTool’s page.

Can I still order an xTool X1?

Yes. xTool has taken X1 orders from everyone since October 28, 2026 at 6:00 PM PDT. If you paid a deposit, complete your order through the link xTool emailed you.

When is the xTool X1 release date?

xTool launched the X1 on October 28, 2026 at 6:00 PM PDT. xTool’s payment and shipping terms, with the date we checked them, are on our xTool X1 price page.

How big is the xTool X1, and what is its work area?

Measured in our workshop on October 11, 2026, the xTool X1 is 39 1/2 in (100.3 cm) wide, 29 3/8 in (74.6 cm) front to back with the 60W MOPA source pack mounted and the lid’s front lip included, and 17 1/2 in (44.5 cm) tall; on xTool’s X1 Mobile Work Stand, the top of the machine sits 45 1/4 in (114.9 cm) off the floor. This is the machine envelope with the source pack installed. It excludes space for the exhaust duct, access and ventilation; allow for those separately when planning installation. xTool’s launch page lists the main unit at 60 kg, whereas its UniCast article said about 50 kg (110 lb); ours is an early unit, so a retail unit may differ slightly. xTool lists the X1’s maximum working area as 615 × 320 mm (24.2 × 12.6 in); its other published figures are in the specifications table. See the measured size table above.

Rear view of our xTool X1 and its mounted 60W source pack, with the stand and cables visible below.
Another angle on the rear of our X1 with the 60W source pack installed. Photo: The Crafty Catsman
Which laser sources does the X1 platform support?

xTool sells five X1 laser configurations: Single CO₂, CO₂ + Diode Galvo, and CO₂ + Diode Galvo with a 30W Fiber, 5W UV or 60W MOPA source added; it also sells each galvo source on its own. Our early unit has CO₂, 20W diode and 60W MOPA installed; that workshop setup does not establish the contents of a retail configuration. Check xTool’s X1 page.

Where can I find the P2, P2S and P3 specifications?

Our P-series guides collect the published specifications and dated price checks for the P2, P2S and P3. This X1 page covers our first impressions and projects so far; we have not published a buying verdict for the X1.

Do you actually have the xTool X1, and is there a review?

Yes. The xTool X1 has been in our workshop since September 2026 with CO₂, 20W diode and 60W MOPA sources installed, and we have been testing it for weeks. xTool sent this early unit for review; xTool has no review or approval of our testing, results, or verdict. This page is an ongoing first look. We will add finished projects as testing continues.

Does the xTool X1 work with LightBurn, and what software runs it?

xTool has not said whether LightBurn can control the X1. For context, xTool says P2S firmware 40.22.011 and later no longer works with LightBurn, and that P3 does not support LightBurn. We run the X1 from xTool Studio on a Mac, and the layered cat design came from xTool’s Atomm software.

· Engineering update

What xTool’s new X1 engineering film adds

xTool’s latest film explains two practical questions: how X1 joins processing zones across a larger design, and how different laser sources stay aligned. These are xTool’s explanations and demonstrations, not independent measurements of a retail machine.

Joining processing zones without a visible boundary

In its September 24 engineering film, xTool says early development left visible boundaries between processing zones. It describes a feathering algorithm that blends those boundaries as the gantry extends the area covered by the galvo.

For artwork spanning a large panel, the useful question is whether fine lines, gradients, and repeated patterns stay consistent across a region boundary. A maximum scan-speed figure cannot answer that.

Calibration is part of the LaserSwap story

The film describes a longest optical path of approximately 1.8 metres and says the engineers had to control accuracy to within 30 microns while making different sources converge at one point. It does not establish a finished-job accuracy guarantee or a tolerance for every retail machine. The optical-path length is not a work-area dimension.

xTool says vision algorithms automate all seven calibration steps after the user places a calibration sheet and clicks once. The film does not establish the duration, required frequency, supported configurations, or recovery procedure if calibration fails.

xTool’s September 23 engineering article identifies the 55W CO₂ head as a separate processing end. Its beam does not pass through the galvo head used by the 20W diode and the supported external sources.

What remains open for buyers

The film identifies Fiber, MOPA, and UV as three source types entering one flying-galvo optical path. Separately, the engineering article says up to three sources can operate sequentially within a task, with automatic switching and no simultaneous emission. It does not explain how that count includes the separate CO₂ head, the 20W diode galvo, and external packs. Automatic selection during a job does not establish automatic physical replacement of a source pack.

Five supported laser families therefore do not establish five connected sources or five sources included in every package. xTool’s launch store lists Single CO₂, CO₂ + Diode Galvo, and CO₂ + Diode Galvo with one added Fiber, UV or MOPA source, and sells each galvo source on its own; check its X1 page.

Sources: xTool’s engineering film, September 24 (5:32); xTool’s engineering article, September 23(paid link). The film link is live; no public archive was available when checked.

The current X1 buying picture

xTool X1 at a glance

Here is what xTool has confirmed—and what buyers still need before choosing an X1 configuration.

55W CO₂ head
55W CO₂ · 20W diodeConfirmed in xTool’s written release and Academy article. Installed in our workshop unit; xTool’s X1 launch page lists the configurations that include it.
Laser Swap™
30W Fiber · 60W MOPA · 5W UVxTool’s modular laser-source system. Supported laser-source families; this is not a package contents list.
Hybrid Motion™
Up to 6,000 mm/sxTool’s name for the hybrid motion architecture. Manufacturer ceiling; not measured throughput.
Launch status
Launched October 28, 2026xTool opened X1 orders to everyone at 6:00 PM PDT; it does not promise a delivery date for any one order.
Maximum working area
615 × 320 mm (24.2 × 12.6 in)xTool’s surface-engraving figure, checked October 31, 2026; processing height is 150 mm for CO₂ and 140 mm for the galvo sources. Installation clearance is not included; our measured size is in the size table.
Bundle contents
Not yet listed hereEach configuration also comes as a Versatile or All-in-One Bundle; xTool’s X1 page lists what each bundle includes.
Official sources checked October 31, 2026.

We update this guide when xTool changes its X1 page or a workshop project is finished.

xTool confirmed on September 1, 2026 that our early X1 evaluation unit had shipped. The unit arrived in September 2026. Hands-on testing is underway.xTool sent this early X1 unit for review. xTool has no review or approval of our testing, results, or verdict.

The workshop question

What if your workshop could grow without adding another full-size machine?

X1 aims to put broader creative range inside one adaptable footprint.

Official X1 product image. The starting price and our measured size table are near the top of this page.
Official xTool X1 product image used to frame the workshop-fit question

The workshop doesn’t get bigger. The machine has to do more.

The X1 question we’ll put to work

One footprint. More creative range.

We will test whether modules can protect shop space, reduce handoffs, and keep the work moving without giving up the depth a focused machine can provide.

Let’s Dive into the X1

Choose the question that sounds most like your workshop, then follow X1 into the first projects and how the platform works.

xTool X1 guide

Could one modular machine become the new workshop staple?

Guide updated · October 31What the teaser shows

That is the promise worth examining. xTool’s August 28 written release and September 1 Academy article both specify a 55W CO₂ laser for X1, resolving the conflicting 50W and 55W figures spoken during the livestream. xTool describes a 20W blue-diode galvo path in its published engineering. Its launch store sells a CO₂ + Diode Galvo configuration with the 55W CO₂ and the 20W diode galvo, and sells the 20W Diode Galvo Module on its own; xTool says that module is required before a UV, Fiber or MOPA source is added. Our workshop unit has the 20W diode installed, but its three-source setup does not define a retail configuration. xTool’s August 28 written release lists Hybrid Motion processing speeds up to 6,000 mm/s. This is a manufacturer ceiling, not measured throughput. xTool publicly lists support for 30W Fiber, 60W MOPA, and 5W UV laser sources through its Laser Swap system.

xTool X1 buyer guideChecked October 31, 2026

The new workshop-staple question

More making power without more machines taking over the room.

X1’s appeal is the chance to build one adaptable center for cutting, engraving, detail work, and future laser modules. That could keep creators focused and nimble while protecting the workshop space that is hardest to replace.

The received configuration determines which module-specific projects enter the test protocol.xTool confirmed on September 1, 2026 that our early X1 evaluation unit had shipped. The unit arrived in September 2026. Hands-on testing is underway.

Our X1 has CO₂, 20W diode and 60W MOPA sources installed; that is one early unit’s setup, not a retail package.

Official xTool X1 enclosed laser platform

Why X1 is different

Three technologies power the X1 platform.

Hybrid Motion™, Laser Swap™, and UniCast Frame define xTool’s announced platform architecture.

  1. 01 · Motion architecture

    Hybrid Motion™

    Gantry reach meets galvo speed.

    xTool publicly describes X1 as a hybrid gantry-and-galvo system. Hybrid Motion is the name xTool gives the motion architecture that brings those two approaches together. xTool’s August 28 written release and September 1 Academy article both specify a 55W CO₂ laser for X1, resolving the conflicting 50W and 55W figures spoken during the livestream. xTool describes a 20W blue-diode galvo path in its published engineering. Its launch store sells a CO₂ + Diode Galvo configuration with the 55W CO₂ and the 20W diode galvo, and sells the 20W Diode Galvo Module on its own; xTool says that module is required before a UV, Fiber or MOPA source is added. Our workshop unit has the 20W diode installed, but its three-source setup does not define a retail configuration. xTool’s August 28 written release lists Hybrid Motion processing speeds up to 6,000 mm/s. This is a manufacturer ceiling, not measured throughput. xTool’s X1 launch page, checked October 31, 2026, lists a maximum working area of 615 × 320 mm (24.2 × 12.6 in) for surface engraving, 600 × 300 mm for glass inner engraving in the top 50 mm at refractive index 1.54 (60 × 300 mm from 50 to 100 mm deep), and 415 × 225 mm for metal embossing with the Dust Hood for Embossing. It lists processing height at 150 mm for CO₂ and 140 mm for the galvo sources.

    • 55WCO₂ head
    • 20WDiode galvo path
    • Up to 6,000 mm/sxTool maximum

    Detailed engraving and larger cutting no longer have to live on different machine types.

    We’ll compare complete job time—not only peak movement speed—during hands-on testing.
  2. 02 · Modular laser system

    Laser Swap™

    Change the laser, not the whole workshop.

    xTool names Laser Swap as X1’s modular laser system and connects it to expanding the machine across different laser-source families. Its September 9 Academy article describes each added source as a cartridge mounted on the back of X1 that feeds one shared galvo head through a single optical path, with every source calibrated to the same work coordinates. xTool publicly lists support for 30W Fiber, 60W MOPA, and 5W UV laser sources through its Laser Swap system.

    • 30WFiber
    • 60WMOPA
    • 5WUV

    Whether that range reduces full-size machines or workflow friction is a buyer question. xTool now describes vision-assisted seven-step calibration and identification of the material and processing area, and its launch page lists an 8 MP overview camera, a 12 MP close-up camera and a ranging camera, with LiDAR ranging and autofocus. Software requirements, calibration timing and frequency, and the complete cross-source workflow remain unpublished.

    xTool sells each of the five X1 laser configurations machine only (Standalone) or as a Versatile Bundle or an All-in-One Bundle, and xTool’s X1 page lists what each bundle includes. We have not listed the bundle contents here yet. xTool launched the X1 on October 28, 2026 at 6:00 PM PDT; the launch price of every configuration is on our xTool X1 prices by laser configuration page. Launch offers run through December 6, 2026 at 11:59 PM PST. xTool does not promise a delivery date.
  3. 03 · Structural foundation

    UniCast Frame

    xTool’s named structural foundation for the platform.

    xTool names UniCast Frame as the structural foundation for the X1 platform. xTool’s written release describes UniCast as 4,000-ton high-pressure die casting in automotive-grade aluminum with three die-cast frame sections, and xTool’s X1 page says UniCast replaces nearly 100 parts and 268 screws.

    • 4,000-tonDie casting
    • 3Die-cast sections
    • Nearly 100 / 268Parts / screws replaced

    Long-term rigidity, alignment, and durability remain questions for hands-on testing.

    Long-term precision, thermal stability, and durability belong in our hands-on and ownership testing.

F2 / F2 Ultra · metal and detail

Where X1 gains range—and specialists keep the edge.

X1 could become the shop’s adaptable center: one footprint, modular sources, shared controls, and room to grow. A P3, P2/P2S, or F2/F2 Ultra may still win when the work depends on production scale, a focused CO2 workflow, compact detail work, parallel machines, or failure isolation.

Our setup

Our first projects use the CO₂, 20W diode, and 60W MOPA sources installed on our X1.

Fiber and UV are not part of our setup, so this page shows no results from those sources. Across the installed sources, we will add complete projects, source changes, and repeated files as they are finished.

That testing arrangement is not proof of a final retail bundle. Module-specific projects will cover the specialist paths included with the received unit; UV, MOPA, and Fiber retain their own buying questions when a source is not included.

Follow the X1 story

What we’ll add next.

This is an ongoing first look; we will add finished projects as testing continues.

Read the reader questions →

Question 01

Why could X1 change the shop?

More capability inside one machine could protect space and reduce equipment handoffs.

Question 02

Where do specialists stay stronger?

Focused machines may still lead on scale, depth, parallel production, workflow maturity, or failure isolation.

Question 03

What will our early unit answer?

The received configuration determines how the platform promise is tested across real workshop projects.

Find your shop fit

Is X1 your jack-of-all-trades, or does each job deserve a specialist?

Hybrid Motion™Laser Swap™

xTool’s official August 31 post said X1 was “coming this October.” xTool opened deposits on October 12 and launched the X1 on October 28, 2026 at 6:00 PM PDT, when orders opened to everyone; the deposit period had closed at 5:00 PM PDT that day. The right choice depends on the room you have, the work you repeat, and whether one adaptable machine creates more value than dedicated stations.

Official xTool X1 product artwork showing the enclosed desktop laser machine
Official xTool X1 product image.

The choice beneath the launch

Do you need one adaptable center—or a focused machine that goes deeper?

X1’s strongest case is a shop that values creative range, future options, and protected floor space. Specialist xTool machines remain compelling when one material, workflow, scale, or production rhythm does most of the work.

Use seven questions to locate your path.

Compare primary materials, required work area, creative range, parallel throughput, software continuity, bundle contents, and complete installed cost. The cards below show how those answers tend to group.

Four workshop profiles

Which shop sounds most like yours?

Find your closest match, then follow it into the package and machine comparison that matters most.

Strong X1 question
Limited spaceBroad creative range

The space-limited generalist

X1 could be the workshop center this maker has been waiting for.

  • Several materials or product types matter
  • Every full-size machine displaces useful working space
  • Future modules may be more practical than future machines

Start here if your shop needs range, but the room cannot keep expanding.

Specialist may lead
CO2 productionLarge repeat work

The production-first CO2 shop

P3 or an established P2/P2S workflow may remain the sharper tool.

  • Large-format handling or CO2 depth drives revenue
  • Parallel work matters more than consolidating machines
  • Downtime isolation and proven accessories protect output

Start here if one focused production lane does most of the paid work.

MOPA comparison
Fine detailMetal-focused work

The detail-and-metal specialist

F2 or F2 Ultra may still provide the more focused bench for small, fast, detailed work.

  • Metal marking and compact detail work dominate
  • A smaller station and fast galvo workflow suit the product mix
  • X1 only wins if its added range earns the larger platform

Start here if specialist speed and a focused work envelope are strengths, not limitations.

The original announcement

X1 entered the public record on August 13.

xTool named X1, used the phrase “The Next-Gen Laser Machine,” and paired it with dark, largely obscured teaser artwork.

  1. Official teaser published

    xTool named X1, used the phrase “The Next-Gen Laser Machine,” and paired it with dark, largely obscured teaser artwork.

    Read the official teaser
Official xTool X1 teaser artwork showing a dark, largely obscured machine silhouette
Follow the xTool X1

We are testing the X1 in our workshop.

Get an email when we add a finished X1 project or xTool changes its X1 page. Bookmark this guide if you prefer to check back.

Privacy details

Prefer to check back on your own?

Current chapter: First look